cartreader/Cart_Reader/INTV.ino

966 lines
25 KiB
Arduino
Raw Normal View History

//******************************************
// INTELLIVISION MODULE
//******************************************
#ifdef enable_INTV
// Mattel Intellivision
// Cartridge Pinout
// 44P 2.54mm pitch connector
//
// TOP SIDE BOTTOM SIDE
// (EVEN) (ODD)
// +-------+
// GND -| 2 1 |- GND
// CBLNK -| 4 3 |- /MSYNC
// EXT AUD -| 6 5 |- DB7
// EXT VID -| 8 7 |- DB8
// MCLK -| 10 9 |- DB6
// RESET -| 12 11 |- DB9
// SR1 -| 14 13 |- DB5
// VOICE -| 16 15 |- DB10
// VOICE -| 18 17 |- DB4
// GND -| 20 19 |- DB11
// GND -| 22 21 |- DB3
// GND -| 24 23 |- DB12
// GND -| 26 25 |- DB13
// GND -| 28 27 |- DB2
// /BUSAK -| 30 29 |- DB14
// BC1 -| 32 31 |- DB1
// BC2 -| 34 33 |- DB0
// BDIR -| 36 35 |- DB15
// BDIR -| 38 37 |- BDIR
// BC2 -| 40 39 |- BC2
// BC1 -| 42 41 |- BC1
// GND -| 44 43 |- VCC(+5V)
// +-------+
// CONTROL PINS:
// /MSYNC(PH3)- PIN 3 [ROM PIN 14]
// BC1(PH4) - PIN 41 [ROM PIN 28]
// BC2(PH5) - PIN 39 [ROM PIN 27]
// BDIR(PH6) - PIN 37 [ROM PIN 26]
// NOTE: BDIR/BC1/BC2 ONLY CONNECTED TO BOTTOM (ODD) PINS
// NOT CONNECTED:
// RESET(PH0) - N/C - GND IN CART
// MCLK(PH1) - N/C - GND IN CART
// BUS PROTOCOL COMMANDS - BDIR/BC1/BC2
// NO ACTION (NACT): 0/0/0
// ADDR TO REG (ADAR): 0/1/0
// INT ADDR TO BUS (IAB): 0/0/1
// DATA TO BUS (DTB): 0/1/1
// BUS TO ADDR (BAR): 1/0/0
// DATA WRITE (DW): 1/1/0
// DATA WRITE STROBE (DWS): 1/0/1
// INTERRUPT ACK (INTAK): 1/1/1
// Cart Configurations
// Format = {mapper,romlo,romhi,ramsize}
static const byte PROGMEM intvmapsize [] = {
0, 0, 2, 0, // default mattel up to 32K (8K/16K/24K/32K)
1, 1, 3, 0, // demo cart 16K, championship tennis 32K, wsml baseball 48K
2, 1, 3, 0, // up to 48K (16K/32K/48K)
3, 4, 4, 0, // tower of doom 48K
4, 0, 1, 1, // uscf chess 16K + RAM 1K
5, 2, 3, 0, // congo bongo/defender/pac-man 24K, dig dug 32K
6, 1, 1, 0, // centipede 16K
7, 1, 1, 0, // imagic carts 16K
8, 1, 1, 0, // mte-201 test cart 16K
9, 3, 3, 2, // triple challenge 32K + RAM 2K
};
byte intvmapcount = 10; // (sizeof(mapsize)/sizeof(mapsize[0])) / 4;
boolean intvmapfound = false;
byte intvmapselect;
int intvindex;
byte INTV[] = {8, 16, 24, 32, 48};
byte intvlo = 0; // Lowest Entry
byte intvhi = 4; // Highest Entry
byte intvmapper;
byte newintvmapper;
byte intvsize;
byte newintvsize;
// EEPROM MAPPING
// 07 MAPPER
// 08 ROM SIZE
//******************************************
// Menu
//******************************************
// Base Menu
static const char intvMenuItem1[] PROGMEM = "Select Cart";
static const char intvMenuItem2[] PROGMEM = "Read ROM";
static const char intvMenuItem3[] PROGMEM = "Set Mapper + Size";
static const char intvMenuItem4[] PROGMEM = "Reset";
static const char* const menuOptionsINTV[] PROGMEM = {intvMenuItem1, intvMenuItem2, intvMenuItem3, intvMenuItem4};
void setup_INTV()
{
// Set Address Pins to Output (UNUSED)
//A0-A7
DDRF = 0xFF;
//A8-A15
DDRK = 0xFF;
//A16-A23
DDRL = 0xFF;
// Set Control Pins to Output
// ---(PH0) ---(PH1) /MSYNC(PH3) BC1(PH4) BC2(PH5) BDIR(PH6)
DDRH |= (1 << 0) | (1 << 1) | (1 << 3) | (1 << 4) | (1 << 5) | (1 << 6);
// Set TIME(PJ0) to Output (UNUSED)
DDRJ |= (1 << 0);
// Set Pins (DB0-DB15) to Input
DDRC = 0x00;
DDRA = 0x00;
// Setting Control Pins to HIGH
// ---(PH0) ---(PH1) /MSYNC(PH3) BC1(PH4) BC2(PH5) BDIR(PH6)
PORTH |= (1 << 0) | (1 << 1) | (1 << 3) | (1 << 4) | (1 << 5) | (1 << 6);
// Set Unused Pins HIGH
PORTF = 0xFF; // A0-A7
PORTK = 0xFF; // A8-A15
PORTL = 0xFF; // A16-A23
PORTJ |= (1 << 0); // TIME(PJ0)
checkStatus_INTV();
strcpy(romName, "INTV");
mode = mode_INTV;
}
void intvMenu()
{
convertPgm(menuOptionsINTV, 4);
uint8_t mainMenu = question_box(F("INTELLIVISION MENU"), menuOptions, 4, 0);
switch (mainMenu)
{
case 0:
// Select Cart
setCart_INTV();
setup_INTV();
break;
case 1:
// Read ROM
sd.chdir("/");
readROM_INTV();
sd.chdir("/");
break;
case 2:
// Set Mapper
setMapper_INTV();
checkMapperSize_INTV();
setROMSize_INTV();
break;
case 3:
// reset
resetArduino();
break;
}
}
//******************************************
// INTELLIVISION BUS PROTOCOL COMMANDS
//******************************************
// CONTROL PINS - BDIR/BC1/BC2
// NO ACTION (NACT): 0/0/0
// ADDR TO REG (ADAR): 0/1/0 [NOTE: ORDER BDIR/BC1/BC2]
// DATA TO BUS (DTB): 0/1/1
// BUS TO ADDR (BAR): 1/0/0
// DATA WRITE (DW): 1/1/0 [NOTE: ORDER BDIR/BC1/BC2]
// DATA WRITE STROBE (DWS): 1/0/1 [NOTE: ORDER BDIR/BC1/BC2]
// IMMEDIATE MODE DATA READ SEQUENCE: BAR-NACT-DTB-NACT
// IMMEDIATE MODE DATA WRITE SEQUENCE: BAR-NACT-DW-DWS-NACT
// DIRECT ADDRESSING MODE READ SEQUENCE: BAR-NACT-ADAR-NACT-DTB-NACT
// NO ACTION (NACT) - 0/0/0
void NACT_INT()
{
// Switch BC1(PH4) + BC2(PH5) + BDIR(PH6) to LOW
PORTH &= ~(1 << 4) & ~(1 << 5) & ~(1 << 6);
// DB0..DB15 INPUT
DDRC = 0x00;
DDRA = 0x00;
}
// SET ADDRESS - BUS TO ADDR (BAR) - 1/0/0
void BAR_INT()
{
// Switch BDIR(PH6) to HIGH
PORTH |= (1 << 6);
// Switch BC1(PH4) + BC2(PH5) to LOW
PORTH &= ~(1 << 4) & ~(1 << 5);
// Address OUT
DDRC = 0xFF;
DDRA = 0xFF;
}
// READ DATA - DATA TO BUS (DTB) - 0/1/1
void DTB_INT()
{
// Switch BDIR(PH6) to LOW
PORTH &= ~(1 << 6);
// Switch BC1(PH4) + BC2(PH5) to HIGH
PORTH |= (1 << 4) | (1 << 5);
// Data IN
DDRC = 0x00;
DDRA = 0x00;
}
// ADDRESS DATA TO ADDRESS REGISTER (ADAR) - 0/1/0
void ADAR_INT()
{
// Switch BC2(PH5) + BDIR(PH6) to LOW
PORTH &= ~(1 << 5) & ~(1 << 6);
// Switch BC1(PH4) to HIGH
PORTH |= (1 << 4);
}
// DATA WRITE PAIRED COMMAND - DW + DWS
// DATA SHOULD BE STABLE ACROSS BOTH
// DATA WRITE (DW) - 1/1/0
void DW_INT()
{
// Switch BC1(PH4) + BDIR(PH6) to HIGH
PORTH |= (1 << 4) | (1 << 6);
// Switch BC2(PH5) to LOW
PORTH &= ~(1 << 5);
}
// DATA WRITE STROBE (DWS) - 1/0/1
void DWS_INT()
{
// Switch BC2(PH5) + BDIR(PH6) to HIGH
PORTH |= (1 << 5) | (1 << 6);
// Switch BC1(PH4) to LOW
PORTH &= ~(1 << 4);
}
//******************************************
// READ CODE
//******************************************
uint16_t readData_INTV(uint32_t addr)
{
PORTC = addr & 0xFF;
PORTA = (addr >> 8) & 0xFF;
BAR_INT();
// Wait for bus
// 5 x 62.5ns = 312.5ns
NOP; NOP; NOP; NOP; NOP;
NACT_INT();
NOP; NOP; NOP; NOP; NOP;
DTB_INT();
NOP; NOP; NOP; NOP; NOP;
uint16_t ret = (((PINA & 0xFF) << 8) | (PINC & 0xFF));
NACT_INT();
NOP; NOP; NOP; NOP; NOP;
return ret;
}
// MAPPER ROM ADDRESSES
// 0: 0x50-0x70,0xD0-0xE0,0xF0-0x100, // default mattel up to 32K (8K/16K/24K/32K)
// 1: 0x50-0x70,0xD0-0x100, // demo cart 16K, championship tennis 32K, wsml baseball 48K
// 2: 0x50-0x70,0x90-0xC0,0xD0-0xE0, // up to 48K (16K/32K/48K)
// 3: 0x50-0x70,0x90-0xB0,0xD0-0xE0,0xF0-0x100, // tower of doom 48K
// 4: 0x50-0x70, // uscf chess 16K + RAM 1K
// 5: 0x50-0x80,0x90-0xC0, // congo bongo/defender/pac-man 24K, dig dug 32K
// 6: 0x60-0x80, // centipede 16K
// 7: 0x48-0x68, // imagic carts 16K
// 8: 0x50-0x60,0x70-0x80, // mte-201 test cart 16K
// 9: 0x50-0x70,0x90-0xB0,[0xC0-0xC8,0xD0-0xD8] // triple challenge 32K + RAM 2K [0xC0 + 0xD0 segments are not needed]
void readSegment_INTV(uint32_t startaddr, uint32_t endaddr)
{
for (uint32_t addr = startaddr; addr < endaddr; addr += 256) {
for (uint16_t w = 0; w < 256; w++) {
uint16_t temp = readData_INTV(addr + w);
sdBuffer[w * 2] = (temp >> 8) & 0xFF;
sdBuffer[(w * 2) + 1] = temp & 0xFF;
}
myFile.write(sdBuffer, 512);
}
}
// MODIFIED READ ROUTINE FOR ALL 10 MAPPERS
void readROM_INTV()
{
strcpy(fileName, romName);
strcat(fileName, ".int");
// create a new folder for storing rom file
EEPROM_readAnything(0, foldern);
sprintf(folder, "INTV/ROM/%d", foldern);
sd.mkdir(folder, true);
sd.chdir(folder);
display_Clear();
print_Msg(F("Saving to "));
print_Msg(folder);
println_Msg(F("/..."));
display_Update();
// open file on sdcard
if (!myFile.open(fileName, O_RDWR | O_CREAT))
print_Error(F("Can't create file on SD"), true);
// write new folder number back to EEPROM
foldern++;
EEPROM_writeAnything(0, foldern);
switch (intvmapper) {
case 0: //default mattel up to 32K (8K/16K/24K/32K)
readSegment_INTV(0x5000, 0x6000); // 8K
if (intvsize > 0) {
readSegment_INTV(0x6000, 0x7000); // +8K = 16K
if (intvsize > 1) {
readSegment_INTV(0xD000, 0xE000); // +8K = 24K
if (intvsize > 2)
readSegment_INTV(0xF000, 0x10000); // +8K = 32K
}
}
break;
case 1: // demo cart/championship tennis/wsml baseball
readSegment_INTV(0x5000, 0x7000); // 16K Demo Cart
if (intvsize > 1) {
readSegment_INTV(0xD000, 0xE000); // +8K = 24K [NONE]
if (intvsize > 2) {
readSegment_INTV(0xE000, 0xF000); // +8K = 32K Championship Tennis
if (intvsize > 3) {
readSegment_INTV(0xF000, 0x10000); // +8K = 40K WSML Baseball [MISSING 8K ECS BANK]
// ecs bank switch
ecsBank(0xFFFF, 0x1); // switch ecs page 1 to 0xF000
readSegment_INTV(0xF000, 0x10000); // + 8K = 48K WSML Baseball
ecsBank(0xFFFF, 0x0); // reset ecs page 0 to 0xF000
}
}
}
break;
case 2: // up to 48K (16K/32K/48K)
readSegment_INTV(0x5000, 0x7000); // 16K
if (intvsize > 1) {
readSegment_INTV(0x9000, 0xA000); // +8K = 24K [NONE]
if (intvsize > 2) {
readSegment_INTV(0xA000, 0xB000); // +8K = 32K
if (intvsize > 3) {
readSegment_INTV(0xB000, 0xC000); // +8K = 40K
readSegment_INTV(0xD000, 0xE000); // +8K = 48K
}
}
}
break;
case 3: // tower of doom 48K
readSegment_INTV(0x5000, 0x7000); // 16K
readSegment_INTV(0x9000, 0xB000); // +16K = 32K
readSegment_INTV(0xD000, 0xE000); // +8K = 40K
readSegment_INTV(0xF000, 0x10000); // +8K = 48K
break;
case 4: // chess 16K
PORTH &= ~(1 << 3); // /MSYNC to LOW
readSegment_INTV(0x5000, 0x6000); // 8K
PORTH |= (1 << 3); // /MSYNC to HIGH
readSegment_INTV(0x6000, 0x7000); // 8K
break;
case 5:// congo bongo/defender/pac-man/dig dug
readSegment_INTV(0x5000, 0x7000); // 16K
readSegment_INTV(0x7000, 0x8000); // +8K = 24K Congo Bongo/Defender/Pac-Man
if (intvsize > 2) {
readSegment_INTV(0x9000, 0xA000); // +8K = 32K Dig Dug
//readSegment_INTV(0xA000,0xC000); // +16K = 48K [UNUSED]
}
break;
case 6: // centipede 16K
readSegment_INTV(0x6000, 0x8000); // 16K
break;
case 7: // imagic carts 16K
readSegment_INTV(0x4800, 0x6800); // 16K
break;
case 8: //mte-201 test cart 16K
readSegment_INTV(0x5000, 0x6000); // 8K
readSegment_INTV(0x7000, 0x8000); // +8K = 16K
break;
case 9: // triple challenge 32K [KNOWN ROM 44K BAD!]
readSegment_INTV(0x5000, 0x7000); // 16K
readSegment_INTV(0x9000, 0xB000); // +16K = 32K
// 0xC000 + 0xD000 SEGMENTS ARE NOT NEEDED (PER INTVNUT POST)
// readSegment_INTV(0xC000,0xC800); // +4K = 36K
// readSegment_INTV(0xD000,0xE000); // +8K = 44K
break;
}
myFile.close();
// Compare CRC32 to database and rename ROM if found
compareCRC("intv.txt", 0, 1, 0);
println_Msg(F(""));
println_Msg(F("Press Button..."));
display_Update();
wait();
}
// ECS BANKSWITCH FOR WSML BASEBALL
// write $xA5y to $xFFF
// x = rom location ($x000 - $xFFF)
// y = page (up to 16 - WSML Baseball only uses 0/1)
void ecsBank(uint32_t addr, uint8_t bank) {
uint16_t ecsdata = (addr & 0xF000) + 0x0A50 + bank; // $xA5y
// Data OUT
DDRA = 0xFF;
DDRC = 0xFF;
// Set Address
PORTA = (addr >> 8) & 0xFF;
PORTC = addr & 0xFF;
BAR_INT();
NOP; NOP; NOP; NOP; NOP;
NACT_INT();
NOP;
// Data OUT
DDRA = 0xFF;
DDRC = 0xFF;
PORTA = (ecsdata >> 8) & 0xFF; // $xA
PORTC = ecsdata & 0xFF; // $5y
DW_INT();
NOP; NOP; NOP; NOP; NOP;
DWS_INT();
NOP; NOP; NOP; NOP; NOP;
NACT_INT();
NOP; NOP; NOP; NOP; NOP;
}
//******************************************
// MAPPER CODE
//******************************************
void setMapper_INTV()
{
#if (defined(enable_OLED) || defined(enable_LCD))
int b = 0;
int i = 0;
// Check Button Status
#if defined(enable_OLED)
buttonVal1 = (PIND & (1 << 7)); // PD7
#elif defined(enable_LCD)
boolean buttonVal1 = (PING & (1 << 2)); // PG2
#endif
if (buttonVal1 == LOW) { // Button Pressed
while (1) { // Scroll Mapper List
#if defined(enable_OLED)
buttonVal1 = (PIND & (1 << 7)); // PD7
#elif defined(enable_LCD)
boolean buttonVal1 = (PING & (1 << 2)); // PG2
#endif
if (buttonVal1 == HIGH) { // Button Released
// Correct Overshoot
if (i == 0)
i = intvmapcount - 1;
else
i--;
break;
}
display_Clear();
print_Msg(F("Mapper: "));
intvindex = i * 4;
intvmapselect = pgm_read_byte(intvmapsize + intvindex);
println_Msg(intvmapselect);
display_Update();
if (i == (intvmapcount - 1))
i = 0;
else
i++;
delay(250);
}
}
display_Clear();
print_Msg(F("Mapper: "));
intvindex = i * 4;
intvmapselect = pgm_read_byte(intvmapsize + intvindex);
println_Msg(intvmapselect);
println_Msg(F(""));
#if defined(enable_OLED)
println_Msg(F("Press left to Change"));
println_Msg(F("and right to Select"));
#elif defined(enable_LCD)
println_Msg(F("Rotate to Change"));
println_Msg(F("Press to Select"));
#endif
display_Update();
while (1) {
b = checkButton();
if (b == 2) { // Previous Mapper (doubleclick)
if (i == 0)
i = intvmapcount - 1;
else
i--;
// Only update display after input because of slow LCD library
display_Clear();
print_Msg(F("Mapper: "));
intvindex = i * 4;
intvmapselect = pgm_read_byte(intvmapsize + intvindex);
println_Msg(intvmapselect);
println_Msg(F(""));
#if defined(enable_OLED)
println_Msg(F("Press left to Change"));
println_Msg(F("and right to Select"));
#elif defined(enable_LCD)
println_Msg(F("Rotate to Change"));
println_Msg(F("Press to Select"));
#endif
display_Update();
}
if (b == 1) { // Next Mapper (press)
if (i == (intvmapcount - 1))
i = 0;
else
i++;
// Only update display after input because of slow LCD library
display_Clear();
print_Msg(F("Mapper: "));
intvindex = i * 4;
intvmapselect = pgm_read_byte(intvmapsize + intvindex);
println_Msg(intvmapselect);
println_Msg(F(""));
#if defined(enable_OLED)
println_Msg(F("Press left to Change"));
println_Msg(F("and right to Select"));
#elif defined(enable_LCD)
println_Msg(F("Rotate to Change"));
println_Msg(F("Press to Select"));
#endif
display_Update();
}
if (b == 3) { // Long Press - Execute (hold)
newintvmapper = intvmapselect;
break;
}
}
display.setCursor(0, 56);
print_Msg(F("MAPPER "));
print_Msg(newintvmapper);
println_Msg(F(" SELECTED"));
display_Update();
delay(1000);
#else
setmapper:
String newmap;
intvmapfound = false;
Serial.print(F("Enter Mapper [0-9]: "));
while (Serial.available() == 0) {}
newmap = Serial.readStringUntil('\n');
Serial.println(newmap);
newintvmapper = newmap.toInt();
for (int i = 0; i < intvmapcount; i++) {
intvindex = i * 4;
intvmapselect = pgm_read_byte(intvmapsize + intvindex);
if (newintvmapper == intvmapselect)
intvmapfound = true;
}
if (intvmapfound == false) {
Serial.println(F("MAPPER NOT SUPPORTED!"));
Serial.println(F(""));
newintvmapper = 0;
goto setmapper;
}
#endif
EEPROM_writeAnything(7, newintvmapper);
intvmapper = newintvmapper;
}
void checkMapperSize_INTV() {
for (int i = 0; i < intvmapcount; i++) {
intvindex = i * 4;
byte mapcheck = pgm_read_byte(intvmapsize + intvindex);
if (mapcheck == intvmapper) {
intvlo = pgm_read_byte(intvmapsize + intvindex + 1);
intvhi = pgm_read_byte(intvmapsize + intvindex + 2);
break;
}
}
}
void setROMSize_INTV()
{
#if (defined(enable_OLED) || defined(enable_LCD))
display_Clear();
if (intvlo == intvhi)
newintvsize = intvlo;
else {
int b = 0;
int i = intvlo;
// Only update display after input because of slow LCD library
display_Clear();
print_Msg(F("ROM Size: "));
println_Msg(INTV[i]);
println_Msg(F(""));
#if defined(enable_OLED)
println_Msg(F("Press left to Change"));
println_Msg(F("and right to Select"));
#elif defined(enable_LCD)
println_Msg(F("Rotate to Change"));
println_Msg(F("Press to Select"));
#endif
display_Update();
while (1) {
b = checkButton();
if (b == 2) { // Previous (doubleclick)
if (i == intvlo)
i = intvhi;
else
i--;
// Only update display after input because of slow LCD library
display_Clear();
print_Msg(F("ROM Size: "));
println_Msg(INTV[i]);
println_Msg(F(""));
#if defined(enable_OLED)
println_Msg(F("Press left to Change"));
println_Msg(F("and right to Select"));
#elif defined(enable_LCD)
println_Msg(F("Rotate to Change"));
println_Msg(F("Press to Select"));
#endif
display_Update();
}
if (b == 1) { // Next (press)
if (i == intvhi)
i = intvlo;
else
i++;
display_Clear();
print_Msg(F("ROM Size: "));
println_Msg(INTV[i]);
println_Msg(F(""));
#if defined(enable_OLED)
println_Msg(F("Press left to Change"));
println_Msg(F("and right to Select"));
#elif defined(enable_LCD)
println_Msg(F("Rotate to Change"));
println_Msg(F("Press to Select"));
#endif
display_Update();
}
if (b == 3) { // Long Press - Execute (hold)
newintvsize = i;
break;
}
}
display.setCursor(0, 56); // Display selection at bottom
}
print_Msg(F("ROM SIZE "));
print_Msg(INTV[newintvsize]);
println_Msg(F("K"));
display_Update();
delay(1000);
#else
if (intvlo == intvhi)
newintvsize = intvlo;
else {
setrom:
String sizeROM;
for (int i = 0; i < (intvhi - intvlo + 1); i++) {
Serial.print(F("Select ROM Size: "));
Serial.print(i);
Serial.print(F(" = "));
Serial.print(INTV[i + intvlo]);
Serial.println(F("K"));
}
Serial.print(F("Enter ROM Size: "));
while (Serial.available() == 0) {}
sizeROM = Serial.readStringUntil('\n');
Serial.println(sizeROM);
newintvsize = sizeROM.toInt() + intvlo;
if (newintvsize > intvhi) {
Serial.println(F("SIZE NOT SUPPORTED"));
Serial.println(F(""));
goto setrom;
}
}
Serial.print(F("ROM Size = "));
Serial.print(INTV[newintvsize]);
Serial.println(F("K"));
#endif
EEPROM_writeAnything(8, newintvsize);
intvsize = newintvsize;
}
void checkStatus_INTV()
{
EEPROM_readAnything(7, intvmapper);
EEPROM_readAnything(8, intvsize);
if (intvmapper > 9) {
intvmapper = 0;
EEPROM_writeAnything(7, intvmapper);
}
if (intvsize > 4) {
intvsize = 0;
EEPROM_writeAnything(8, intvsize);
}
#if (defined(enable_OLED) || defined(enable_LCD))
display_Clear();
println_Msg(F("INTELLIVISION READER"));
println_Msg(F("CURRENT SETTINGS"));
println_Msg(F(""));
print_Msg(F("MAPPER: "));
println_Msg(intvmapper);
print_Msg(F("ROM SIZE: "));
print_Msg(INTV[intvsize]);
println_Msg(F("K"));
display_Update();
wait();
#else
Serial.print(F("CURRENT MAPPER: "));
Serial.println(intvmapper);
Serial.print(F("CURRENT ROM SIZE: "));
Serial.print(INTV[intvsize]);
Serial.println(F("K"));
Serial.println(F(""));
#endif
}
//******************************************
// CART SELECT CODE
//******************************************
void setCart_INTV() {
char gamename[100];
char tempStr2[2];
char crc_search[9];
//go to root
sd.chdir();
// Select starting letter
byte myLetter = starting_letter();
// Open database
if (myFile.open("intv.txt", O_READ)) {
// Skip ahead to selected starting letter
if ((myLetter > 0) && (myLetter <= 26)) {
while (myFile.available()) {
// Read current name
get_line(gamename, &myFile, 96);
// Compare selected letter with first letter of current name until match
while (gamename[0] != 64 + myLetter) {
skip_line(&myFile);
skip_line(&myFile);
get_line(gamename, &myFile, 96);
}
break;
}
// Rewind one line
for (byte count_newline = 0; count_newline < 2; count_newline++) {
while (1) {
if (myFile.curPosition() == 0) {
break;
}
else if (myFile.peek() == '\n') {
myFile.seekSet(myFile.curPosition() - 1);
break;
}
else {
myFile.seekSet(myFile.curPosition() - 1);
}
}
}
if (myFile.curPosition() != 0)
myFile.seekSet(myFile.curPosition() + 2);
}
// Display database
while (myFile.available()) {
display_Clear();
// Read game name
2022-08-03 21:59:11 +02:00
#if defined(enable_OLED)
2022-08-03 19:59:23 +02:00
get_line(gamename, &myFile, 42);
2022-08-03 21:59:11 +02:00
#else
get_line(gamename, &myFile, 96);
#endif
// Read CRC32 checksum
sprintf(checksumStr, "%c", myFile.read());
for (byte i = 0; i < 7; i++) {
sprintf(tempStr2, "%c", myFile.read());
strcat(checksumStr, tempStr2);
}
// Skip over semicolon
myFile.seekSet(myFile.curPosition() + 1);
// Read CRC32 of first 512 bytes
sprintf(crc_search, "%c", myFile.read());
for (byte i = 0; i < 7; i++) {
sprintf(tempStr2, "%c", myFile.read());
strcat(crc_search, tempStr2);
}
// Skip over semicolon
myFile.seekSet(myFile.curPosition() + 1);
// Read mapper
intvmapper = myFile.read() - 48;
// Skip over semicolon
myFile.seekSet(myFile.curPosition() + 1);
// Read rom size
// Read the next ascii character and subtract 48 to convert to decimal
cartSize = myFile.read() - 48;
// Remove leading 0 for single digit cart sizes
if (cartSize != 0) {
cartSize = cartSize * 10 + myFile.read() - 48;
}
else {
cartSize = myFile.read() - 48;
}
// Skip over semicolon
myFile.seekSet(myFile.curPosition() + 1);
// Read SRAM size
byte sramSize = myFile.read() - 48;
// Skip rest of line
myFile.seekSet(myFile.curPosition() + 2);
// Skip every 3rd line
skip_line(&myFile);
2022-08-03 19:59:23 +02:00
println_Msg(F("Select your cartridge"));
println_Msg(F(""));
println_Msg(gamename);
print_Msg(F("Size: "));
print_Msg(cartSize);
println_Msg(F("KB"));
print_Msg(F("Mapper: "));
println_Msg(intvmapper);
#if defined(enable_OLED)
println_Msg(F("Press left to Change"));
println_Msg(F("and right to Select"));
#elif defined(enable_LCD)
println_Msg(F("Rotate to Change"));
println_Msg(F("Press to Select"));
#elif defined(SERIAL_MONITOR)
println_Msg(F("U/D to Change"));
println_Msg(F("Space to Select"));
#endif
display_Update();
int b = 0;
while (1) {
// Check button input
b = checkButton();
// Next
if (b == 1) {
break;
}
// Previous
else if (b == 2) {
for (byte count_newline = 0; count_newline < 7; count_newline++) {
while (1) {
2022-08-03 19:48:12 +02:00
if (myFile.curPosition() == 0) {
break;
}
else if (myFile.peek() == '\n') {
myFile.seekSet(myFile.curPosition() - 1);
break;
}
else {
myFile.seekSet(myFile.curPosition() - 1);
}
}
}
2022-08-03 19:48:12 +02:00
if (myFile.curPosition() != 0)
myFile.seekSet(myFile.curPosition() + 2);
break;
}
// Selection
else if (b == 3) {
//byte INTV[] = {8, 16, 24, 32, 48};
switch (cartSize) {
case 8:
intvsize = 0;
break;
case 16:
intvsize = 1;
break;
case 24:
intvsize = 2;
break;
case 32:
intvsize = 3;
break;
case 48:
intvsize = 4;
break;
default:
intvsize = 0;
break;
}
EEPROM_writeAnything(7, intvmapper);
EEPROM_writeAnything(8, intvsize);
myFile.close();
break;
}
}
}
}
else {
print_Error(F("Database file not found"), true);
}
}
#endif
//******************************************
// End of File
//******************************************