Genesis-Plus-GX/source/cart_hw/eeprom.h
2008-12-11 17:38:29 +00:00

93 lines
3.9 KiB
C

/****************************************************************************
* Genesis Plus 1.2a
* Serial EEPROM support
*
* Copyright (C) Eke-Eke, GC/Wii port
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
***************************************************************************/
#ifndef _EEPROM_H_
#define _EEPROM_H_
typedef enum
{
STAND_BY = 0,
WAIT_STOP,
GET_SLAVE_ADR,
GET_WORD_ADR_7BITS,
GET_WORD_ADR_HIGH,
GET_WORD_ADR_LOW,
WRITE_DATA,
READ_DATA,
} T_EEPROM_STATE;
/* this defines the type of EEPROM inside the game cartridge as Backup RAM
*
* Here are some notes from 8BitWizard (http://www.spritesmind.net/_GenDev/forum):
*
* Mode 1 (7-bit) - the chip takes a single byte with a 7-bit memory address and a R/W bit (24C01)
* Mode 2 (8-bit) - the chip takes a 7-bit device address and R/W bit followed by an 8-bit memory address;
* the device address may contain up to three more memory address bits (24C01 - 24C16).
* You can also string eight 24C01, four 24C02, two 24C08, or various combinations, set their address config lines correctly,
* and the result appears exactly the same as a 24C16
* Mode 3 (16-bit) - the chip takes a 7-bit device address and R/W bit followed by a 16-bit memory address (24C32 and larger)
*
* Also, while most 24Cxx are addressed at 200000-2FFFFF, I have found two different ways of mapping the control lines.
* EA uses SDA on D7 (read/write) and SCL on D6 (write only), and I have found boards using different mapping (I think Accolade)
* which uses D1-read=SDA, D0-write=SDA, D1-write=SCL. Accolade also has a custom-chip mapper which may even use a third method.
*/
typedef struct
{
uint8 address_bits; /* number of bits needed to address memory: 7, 8 or 16 */
uint16 size_mask; /* depends on the max size of the memory (in bytes) */
uint16 pagewrite_mask; /* depends on the maximal number of bytes that can be written in a single write cycle */
uint32 sda_in_adr; /* 68000 memory address mapped to SDA_IN */
uint32 sda_out_adr; /* 68000 memory address mapped to SDA_OUT */
uint32 scl_adr; /* 68000 memory address mapped to SCL */
uint8 sda_in_bit; /* bit offset for SDA_IN */
uint8 sda_out_bit; /* bit offset for SDA_OUT */
uint8 scl_bit; /* bit offset for SCL */
} T_EEPROM_TYPE;
typedef struct
{
uint8 sda; /* current /SDA line state */
uint8 scl; /* current /SCL line state */
uint8 old_sda; /* previous /SDA line state */
uint8 old_scl; /* previous /SCL line state */
uint8 cycles; /* current operation cycle number (0-9) */
uint8 rw; /* operation type (1:READ, 0:WRITE) */
uint16 slave_mask; /* device address (shifted by the memory address width)*/
uint16 word_address; /* memory address */
T_EEPROM_STATE state; /* current operation state */
T_EEPROM_TYPE type; /* EEPROM characteristics for this game */
} T_EEPROM;
/* global variables */
extern T_EEPROM eeprom;
/* Function prototypes */
extern void eeprom_init();
extern void eeprom_write(uint32 address, uint32 value, uint32 word_access);
extern uint32 eeprom_read(uint32 address, uint32 word_access);
#endif