mirror of
https://github.com/Polprzewodnikowy/SummerCart64.git
synced 2024-12-30 23:11:48 +01:00
421d0438f3
This PR completely removes `task.c / task.h` from `sw/controller` STM32 code. Additionally, these changes were implemented: - Updated IPL3 - Added new diagnostic data (voltage and temperature) readout commands for USB and N64 - Fixed some issues with FlashRAM save type - Joybus timings were relaxed to accommodate communication with unsynchronized master controller (like _Datel Game Killer_, thanks @RWeick) - N64 embedded test program now waits for release of button press to proceed - Fixed issue where, in rare circumstances, I2C peripheral in STM32 would get locked-up on power-up - LED blinking behavior on SD card access was changed - LED blink duration on save writeback has been extended - Minor fixes through the entire of hardware abstraction layer for STM32 code - Primer now correctly detects issues with I2C bus during first time programming - `primer.py` script gives more meaningful error messages - Fixed bug where RTC time was always written on N64FlashcartMenu boot - sc64deployer now displays "Diagnostic data" instead of "MCU stack usage"
32 lines
4.0 KiB
Markdown
32 lines
4.0 KiB
Markdown
- [N64 commands](#n64-commands)
|
|
|
|
---
|
|
|
|
## N64 commands
|
|
|
|
| id | name | arg0 | arg1 | rsp0 | rsp1 | description |
|
|
| --- | --------------------- | ------------- | ------------ | ---------------- | -------------- | ---------------------------------------------------------- |
|
|
| `v` | **IDENTIFIER_GET** | --- | --- | identifier | --- | Get flashcart identifier `SCv2` |
|
|
| `V` | **VERSION_GET** | --- | --- | major/minor | revision | Get flashcart firmware version |
|
|
| `c` | **CONFIG_GET** | config_id | --- | --- | current_value | Get config option |
|
|
| `C` | **CONFIG_SET** | config_id | new_value | --- | previous_value | Set config option and get previous value |
|
|
| `a` | **SETTING_GET** | setting_id | --- | --- | current_value | Get persistent setting option |
|
|
| `A` | **SETTING_SET** | setting_id | new_value | --- | --- | Set persistent setting option |
|
|
| `t` | **TIME_GET** | --- | --- | time_0 | time_1 | Get current RTC value |
|
|
| `T` | **TIME_SET** | time_0 | time_1 | --- | --- | Set new RTC value |
|
|
| `m` | **USB_READ** | pi_address | length | --- | --- | Receive data from USB to flashcart |
|
|
| `M` | **USB_WRITE** | pi_address | length/type | --- | --- | Send data from from flashcart to USB |
|
|
| `u` | **USB_READ_STATUS** | --- | --- | read_status/type | length | Get USB read status and type/length |
|
|
| `U` | **USB_WRITE_STATUS** | --- | --- | write_status | --- | Get USB write status |
|
|
| `i` | **SD_CARD_OP** | pi_address | operation | --- | return_data | Perform special operation on SD card |
|
|
| `I` | **SD_SECTOR_SET** | sector | --- | --- | --- | Set starting sector for next SD card R/W operation |
|
|
| `s` | **SD_READ** | pi_address | sector_count | --- | --- | Read sectors from SD card to flashcart |
|
|
| `S` | **SD_WRITE** | pi_address | sector_count | --- | --- | Write sectors from flashcart to SD card |
|
|
| `D` | **DISK_MAPPING_SET** | pi_address | table_size | --- | --- | Set 64DD disk mapping for SD mode |
|
|
| `w` | **WRITEBACK_PENDING** | --- | --- | pending_status | --- | Get save writeback status (is write queued to the SD card) |
|
|
| `W` | **WRITEBACK_SD_INFO** | pi_address | --- | --- | --- | Load writeback SD sector table and enable it |
|
|
| `K` | **FLASH_PROGRAM** | pi_address | length | --- | --- | Program flash with bytes loaded into data buffer |
|
|
| `p` | **FLASH_WAIT_BUSY** | wait | --- | erase_block_size | --- | Wait until flash ready / get block erase size |
|
|
| `P` | **FLASH_ERASE_BLOCK** | pi_address | --- | --- | --- | Start flash block erase |
|
|
| `%` | **DIAGNOSTIC_GET** | diagnostic_id | --- | --- | value | Get diagnostic data |
|